PB Byte Parameter
Byte-Parameter enthalten im Allgemeinen Werte, die die Maschinenkonfiguration repräsentieren,
z.B. kann der Spindelbereichsparameter PB50 für den unteren Bereich den Wert 1 haben, 2 für
den mittleren und 3 für den hohen Bereich.
Beispiel: PB50=2 ( mittlere Getriebestufe )
Byte parameters generally hold values that are representative of the machine configuration.
For example, the spindle range parameter PB50 may hold a value of 1 for low range,
2 for medium, and 3 for high.
Example: PB50=2
Note: Byte parameters are not written in the verify mode.
Byte Parameters
16 ................... Measurement base for leading and trailing digits.
43 .................. Use other tool diameter
Use one value for cutter comp and one for graphics.
Also used in FAST.ATC to check for large tools.
46 ................... Auto⁄Manual mode for Renishaw tool setters
50 ................... Spindle range
54 ................... STL binary files
55 ................... STL metric files
62 ................... Primary handwheel encoder
64 ................... Boot in metric
65 ................... Number of axes
68 ................... Spindle axis
69 ................... Tool change type
Other=0; None=1; Milltronics=2
73 ................... Tool table values diameters or radius
77 ................... Check spindle up to speed
79 ................... G18 is ZX or XZ plane
80 ................... CAD type DXF or IGS
81 ................... Special Flags
82 ................... Offset Round and Tapered Walls
84 ................... Milltronics ATC type
Plunger=0; GenevaTwoStep=1; GenevaOneStep=2;
SwingArm=3; HM20SwingArm=4
85 ................... DPRNT to RS232 or a file
86 ................... Baud rate
87 ................... Parity bits
88 ................... Graph look-ahead
96 ................... Power up with block skip on
97 ................... Power up with optional stop on
98 ................... Slow rapid %
99 ................... MDI mode
For double tool change messages in FAST.ATC
100-109 .......... Post M-code table
110-119 ......... Custom G-code table
120-139 ......... Custom M-code table
148 ................. Tri-color cycle light
151 ................. Log option
176-183 ......... ADC comp axis
185 ................. Allow modal restart
186 ................. Allow Away Offset
187 ................. Spindle probe 10-7
189 ................. Tap up double RPM
190 ................. Check air pressure
191 ................. Scratch
193 ................. # of inserts on the feed and speed calculator
194 ................. Data logging path
0 = Parts 1 = Network
199 ................. Manual option (legacy Centurion1 parameter)
204 ................. Electronic spindle gears
208 ................. Default Trig Help and cutter comp
212 ................. Second handwheel Encoder #
214 ................. Probe input #
215 ................. Cranking factor (for handwheeling through a program)
219 ................. European code
220 ................. Feedhold input
227 ................. Cycle light output
For tri-color EOC light, the other two outputs are hard-coded
229 ................. AC axis drives
230 ................. Third handwheel Encoder #
231 ................. Inverse feedrate in 1⁄sec or 1⁄min
294 ................. Blocks of lookahead
295 ................. Reverse spindle in back gear
338 ................. Look scope blocks
371 ................. Safe zone ON at power-up
393 ................. Log axes
397 ................. Auto rotary brake
400 ................. Ignore ‘tool radius too large’ errors
402 ................. CPU Warning Temperature
404 ................. Front panel type (molded front panel=2)
410 ................. FeedBack on Quill Scale
411 ................. Tool Setting Any Tool, Current Tool
413 ................. Pre-check Software Limits (0=Run Only; 1=Always; 2=Never)
414 ................. Log auto-stop OFF
415 ................. Remote HDW Encoder
416 ................. Quill Scale Encoder
417 ................. Log beats skip
418 ................. Spindle load flag (used in tool load monitoring)
419 ................. Tool Load limits ON
420 ................. Log input
471 ................. Cylinder Parked Axis
472 ................. Cylinder Rotary Axis
475 ................. G5# tool set, add work offset or not.
476 ................. Feedhold G1 and No Spindle 10-8
477 ................. Watch Spindle up to Speed, Check for stalled spindle
479 ................. Chiller Fault Input
480 ................. Tool Carousel Index Button (at rear of machine)
489 ................. Handwheel G54-Z G5# -Z in handwheel
495 ................. 90 Degree Cutter Compensation
500-599 ......... Task global defaults
508 ................. Clockwise coast
509 ................. Clockwise brake
510 ................. Counter clockwise coast
511 ................. Counter clockwise brake
530 ................. Auger ON time
532 ................. Washdown ON time
533 ................. Washdown OFF Time
534 ................. Check Tool Door Open
535 ................. Cooldown Time (Min)
536 ................. Spindle Lube Cycle Time
537 ................. AC Drives
A copy of AC Drives = 229 used in NCB file
538 ................. Put Pot Down on Swing Arm Tool Changers
540 ................. Spindle GearBox
541 ................. Check Drawbar unclamped
542 ................. Yaskawa M5 Spindle motor
545 ................. Front Panel Flags
- bit definition –
FPFLAGS_HOLD_TOOL_CHANGE $01;
FPFLAGS_NOT_OVERRIDE_SWITCH $02;
FPFLAGS_RAPID_OVERRIDE $04;
FPFLAGS_NOT_MANUAL_PANEL $10;
546 ................. Soft trigger
-bit definition - SOFTTRIGGER_AUGER=0x01
547 ................. Tool Changer Type
548 ................. Recycle Pump Time
Used on coolant through spindle (CTS)
549 ................. Check Up-to-speed2
Copy of PB77 for use in NCB files
550 ................. Rotary Brake Delay
552 ................. Up to speed input
555 ................ Auto Rotary Brake2
Copy of PB397 for use in NCB files
556 ................ CTS type
557 ................. Two outputs for pot down on swing arm tool changes
558 ................. Auto Door Opener
559 ................. Specifies Function of aux function button
562 ................. Door open timer
564 ................. Grease Cycle Time
565 ................. Grease Estop Time
566 ................. Specific input # for rear Carousel Index Enable Button
567 ................. Check 4 th Axis brake unclamp
568 ................. Check 4 th Axis brake clamp
569 ................. Check 5 th Axis brake unclamp
570 ................. Check 4 th Axis brake clamp
571 ................. Way lube on time
572 ................. Way lube off time
573 ................. 2 nd tool changer on pocket input #
700 ................. Tool Length
701 ................. Diameter⁄Radius
702 ................. Comp Diam⁄Radius
703 ................. Actual Diam⁄Radius
705 ................. Load Limit
706 ................. High Load
707 ................. Length Wear
708 ................. Diam⁄Radi Wear
709 ................. Max RPM
714 ................. Tool Type
720 ................. Display Column Enable
721 ................. Column 1 Display
722 ................. Column 2 Display
723 ................. Column 3 Display
730 ................. Full Code Window
To keep track of state of Full Code Window (over graphics window) in
formRunVerify
800 ................. Append Stock
801 ................. Stock Type
816-831 ......... Thermal Comp Axis
832-847 ......... Thermal Comp Encoder Master
998 ................. Single block in canned cycles
999 ................. Lathe Mode zero for mills non zero for lathes
1000-1030 ..... Drill Cad file selects